top of page

Dewatering Bags 101: Sizing, Placement, and Maintenance for Clean Pump Discharge

Nov 6
3 min read


BMP Supplies Dewatering Bag

Excavation dewatering is one of the fastest ways to get a site into trouble. A pump moves water off site in minutes, and if that water is carrying silt and sediment, it goes straight into the ditch, the storm system, or the creek. Sediment-laden pump discharge is one of the most common deficiency notices on active construction sites.

A dewatering bag (also called a sediment filtration bag or silt bag) is the standard fix. It is a geotextile bag that connects to the pump discharge hose and filters sediment out of the water before it leaves the site. Simple product, but sizing it wrong or placing it badly is how bags rupture, clog in an hour, or discharge dirty water anyway.

How a dewatering bag works

The bag is made from a non-woven geotextile that lets water pass through while trapping silt and fine sediment inside. The pump discharges into the bag, the bag fills and swells, water weeps out through the fabric, and sediment stays behind. When the bag is full of sediment or the flow rate drops off, you swap it for a fresh one and dispose of the spent bag.

Sizing the bag to the pump

This is the step most crews skip, and it is the one that matters most. A bag that is too small for the pump rate will over-pressurize, balloon, and rupture at the seams or the hose connection.

BMP Dewatering Bag Diagram


Match the bag's flow capacity to the pump's discharge rate. Bag manufacturers rate their products by maximum flow in gallons per minute. Size up, not down: if the pump moves 500 GPM at full throttle, do not spec a 500 GPM bag. Give yourself margin.

Know the sediment load. Clean groundwater is easy on a bag. Silty or clay-heavy water clogs the fabric far faster and effectively reduces the bag's working capacity. On dirty water, size up or plan for more frequent swaps.

When in doubt, run bags in parallel. Two smaller bags manifolded off the discharge line share the flow, last longer between swaps, and give you redundancy if one needs changing mid-shift.

Placement: where the bag sits matters as much as the bag itself

Set the bag on level ground. A bag on a slope migrates, stresses the hose connection, and discharges unevenly. Keep it away from watercourses, storm drains, and property lines. Filtered water still needs somewhere to go: discharge onto a vegetated area or a stone pad where water can infiltrate without carrying sediment off site. Put something under it: a layer of geotextile, straw, or a gravel pad under the bag catches any sediment that escapes. Give it room: bags swell considerably when full, so leave clearance around the bag and keep the discharge hose routed so it does not kink or pull the inlet. Keep the discharge hose as short and straight as practical. Every bend adds back-pressure that works against the bag.

Dewatering Silt Bag BMP Supplies


Maintenance: watch it while it works

A dewatering bag is not install-and-forget. When discharge from the bag slows noticeably while the pump is still running strong, the fabric is clogging: plan the swap now, not when it stops entirely. Look for ballooning or seam stress, which means the bag is undersized for the flow or overdue for a change. Swap before it ruptures: a ruptured bag dumps its entire sediment load at once, which is worse than never having bagged it at all. A full bag is heavy with wet sediment, so have a plan for lifting it with equipment and confirm disposal requirements with the project specs. Do not cut a full bag open on site to empty it.

Dewatering Bag by BMP Supplies


Common mistakes

Connecting the pump directly with no bag because the water looks clean. Sizing to the wrong pump rate. Placing the bag where the filtered discharge runs straight into a storm drain or across a neighboring lot. Leaving a full bag in place over a weekend.

Get the right bag the first time

Dewatering bags come in a range of sizes and flow ratings, and matching the bag to the pump and the sediment load is what makes the difference between clean discharge and a deficiency notice. BMP Supplies manufactures sediment control products in Canada and stocks dewatering bags for common pump rates. Visit bmpsupplies.com or request a quote from our sales team.

 
 
bottom of page